5 Star Sovol Sv06

Classic I3 Structure Combines with Sovol New DesignDifferent from most 3D printers run by wheels in the market, SV06 has a classic I3 structure which avoids wear and tear of wheels and multiple replacements and it is widely applied into industry. We did something new to make it more applicable for household use. Modular design allows you to assemble SV06 within 5 steps easily.. Planetary Dual Gear Direct DriveSovol self-developed All Metal Direct Drive Extruder with planetary dual gear set, provide SV06 with higher drive ratio and a lighter motor, helps to achieve more accurate extrusion. Add large external knob for easy feeding.. 300 High Temp PrintingAll metal Hotend Setup makes it possible to print up to 300. No need to deal with PTFE replacement anymore, and even no need to flash the firmware, you can print with different materials better and more easily. Enclosure is still needed if you want to print over 260.. 25-point Auto LevelingWith inductive sensor, detect the metal print bed through 25 points automatically and compensate the unevenness of the heated bed. The fast, smart, precise detection and compensation help you to get the bed leveled perfectly and get an fantastic first layer. Note Set the height of initial layer to 0.3mm when you slice that would help you to printer better initial layer and make the filament stick to the plate better.. PEI Build PlateThe flexible PEI-coated build plate with mesh surface design makes the prints can be removed easily without any tools. 220220250mm print size, enough for daily use and household use.. Self-developed 32-Bit Silent BoardWith TMC2209 drivers, makes the printer works stably and quietly. UART mode is available, so that more modifications can be done easily for advanced users.. Customer ServiceSovol 3d printers come with one-year warranty and lifetime technical support. Any question on Sovol SV06 3d printer, just click Ask a question through our storefront's page, report an issue through the Your Orders page. We will fast respond within 24 hours and try our best to resolve your every issue..

This PEI magnetic plate are very easy to use, simply stick the magnetic bottom sheet onto your heated bed, then place the steel platform with PEI surface on the top. The maximum temperature for hot bed is 120. Please do not keep the bed heated at too high temp for a continuous long time. Give it a break between 2 prints. Long time printing over 80 would possibly make the magnetic base sheet lose adsorption, even broken.. Textured PEI with Grid Marking Textured PEI surface is harder to come off, more durable than smooth surface.. When printing is complete, let the spring steel sheet cool down enough to around 40 , then easily remove the prints. If the print is still stuck, just gently bend the steel plate and pop it off After many times printings, lightly scour the surface of the PEI with some mild steel wool with 400 grit will have great adhesion or use alcohol to clear it and let it dry.. Sovol flexible PEI build plate is 235235mm9.259.25inch, compatible with Creality 3D printer such as Ender-3 Pro, Ender-3 V2Ender-3, Ender-3 S1, Ender-3 S1 pro, Ender-5, Ender-5 Pro, Ender 5 S1, CR-20, CR-20 Pro, Sovol SV05 SV06 and similarly sized machines.. Simple Installation Made of high quality stainless steel and strong magnetic base, stick the magnetic base to your printing build plate by peeling off the backing paper and sticking it onto your bed, then place the steel plate onto the magnetic base sheet..

Sovol new self-developed upgraded motherboard is equiped with 32-bit MCU and 24V power input, which makes the caculation speed faster, operation control system more sensitive, printing accuracy higher and improve stability.. High quality MOS tube, high imput impedance, low noise below 50 decibels, good thermal stability.. All-round heat dissipation design, each TMC2209 chip have heat sinks, let the cooling system easily cope with more situations.. Support auto leveling, filament sensor and resume printing after a power failure.. Perfect fit for SV06 and SV06 Plus 3D Printer. The firmware presinsalled for SV06, Plug and Play. If your printer is other models except SV06 please flash firmware at first.. If you have any other questions, please let us know. We will reply and provide professional technical support within 24 hours..

Overview of Neptune 3 Pro225x225x280mm8.85x8.85x11 inch market mainstream printing size can meet the needs of most users. With an STM32 motherboard, all axes of ELEGOO Neptune 3 Pro are driven by silent stepper motors for quieter and more precise movement during printing, which reduces the noise as low as 47-48dB. The easy-to-setup printer comes with the main components pre-assembled, as well as a complete tool kit for quick installation.. Dual-Gear Direct ExtruderThe new dual-gear direct drive extruder is made of SUS303 high-quality stainless steel with a 31 reduction ratio and stronger extrusion force for smoother filament feeding and more stable accurate printing, which greatly reduces nozzle clogging and under-extrusion issues, printing effect is better than Bowden extruder. Compatible with multiple filaments such as PLA, TPU, PETG, and ABS.. Nozzle Kit for Better Printing EffectThe nozzle kit contains a TC4 titanium alloy throat pipe, an aluminum alloy flat heat sink structure, and a brass nozzle.The widened aluminum heat sink paired with the front close-fitting efficient cooling fan for a better heat dissipation effect and lower the temperature of the throat pipe, thereby reducing the possibility of nozzle clogging.. Smarter Printing ExperienceAuto mesh bed leveling adopts a non-contact high precision sensor to automatically scan 36 6x6 points of the hotbed and collect data in real-time, and then adjust the Z-axis height to compensate for any irregularities and unevenness of the printing platform. Only applicable to metal printing platforms Smart resume printing the printer will auto-pause when the filament runs out or breaks, and you can resume printing after a power outage.. More Stable PrintingThe Z-axis with dual synchronized lead screws and dual-motor drive for more stable movement of the print head and higher printing accuracy, avoiding the printing deviation driven by a single Z-axis lead screw motor. The 4-wheel V-guide rail pulley is made of POM with more stable movement, low noise, wear resistance, and longer service life..

100 Sovol Original.. This SV06 Hotend kit comes with the heatblock, brass nozzle. thermistor, heating tube, metal heatbreak and silicone cover.. We also sell the extruder, silent board and PEI build plate of SV06 on Amazon now. If you have spare needs you can order them.. More SV06 accessories will be listed for sale on Amazon. If you want to order any accessories we have not sell on Amazon temporarily please let us know through Amazon message. All accessories of SV06 can be ordered from us..

Remove Excess Moisture3D printer filaments are hygroscopic, moisture would cause printing failure. Sovol SH01, a great addition to 3d printer, can remove excess moisture, keep your filament dry and bring you better prints. The surface of prints will be smoother, the layer adhesion increased. No more brittle PLA, PETG, ABS filament.. Real-time Monitoring of Temp and Humidity insideDisplays the humidity and temperature in the dry box in real time. Setting temperature 40 , 45 , 50 C and setting time from 6 hours to 12 hours. If you use SH01 in a room with room temperature under 16, the temperature in the dryer box would not come up to 50. But do not worry, this would not decrease drying effect.. Excellent Power-off Drying ModeSilicone PTFE seal makes it possible to store filaments for a long time without power and protects your filaments from moisture and dirt. You can put 4 bags of desiccants not included in the package inside the dryer box to improve drying efficience quality.. Large Capacity Sovol dryer box can store 2 filament rolls with a width of less than 70 mm or 1 filament roll with a width of less than 150 mm. Please open the PTFE seals on the top of the box during heating for Moisture evaporation.. Heating More Evenly The unique design of the built-in fan in the box is based on the principle of modynamics of air, makes the filament heated more evenly. SH01 makes drying more efficient. Any questions about the product please feel free to contact us. Our technical support team will provide service as soon as we can..

Constant Temprature Keep a constant temperature Printing Enviroment. Reducing the Bad impact to 3D prints. improve the prints stability at warm status. Help Regulate the temperature and reduce drafts for improved print quality and keep curious fingers or paws off your print. Flame Retardant This 3D Printer used aluminum foil inside that resist 600C 800 C to Isolate accidentally fire. aluminum material for more heat retention.. Noise Reduce Enclosed build chamber would Effectively Block the noise during printing. Get a slight reduction in the already low noise out put the printer.. Multifunction Structure hinged doors on the front of Enclosure. 25.6 21.6 29.5 Size Compitable with 99 FDM printers. No glue is required for assembly and can easily disassembled for moving or replacing.. Easy Installation5 minutes quick installation. No extra tools required. With Glass fiber Cube and stainless steel corner that features light and strong..

SUNLU SILK 3D Printer Filament Bundle2kg in Total, 8 Spools of 250g SUNLU 1.75mm SILK filament. Multiple Color Choices, 8 colours BlackWhiteLight GoldSilverBrassRed CopperBlueGreen. Multiple colors satisfy your rich 3d printing creativity.. SUNLU Shiny SILK PLA Filament 1.75mmCompared to regular PLA 3D printer filament, SUNLU SILK PLA 3d printer filament has a glossy, smooth silk surface that does not require polishing. SUNLU fantastic SILK filament has great colour and shine,making it ideal for printing art and craft.Great SILK PLA filament for any 3D print job.It has a nice silk looking shine on prints.. SILK Filament Recommend SettingsSUNLU premium SILK filament offer the advantage of incredible ease of 3d printing. SUNLU SILK filament 1.75mm ,optimized print quality,high purity with low shrinkage and superb interlayer adhesion. Recommended SUNLU SILK filament Print nozzle temperature 200-230, Hot bed temp 60C-80C, Print speed 30-60mms.. Neatly Wound Filament SUNLU has a professional production line with strict control of neatly lined up lines to avoid knots during printing.Completely mechanical wire winding and strict manual checks to ensure neat lines with few kinks, avoiding possible breaks.. High Precision - 0.02mm Tolerance SILK filament1.75mm SILK 3D filament Tolerance Level 0.02mm. 0.25KG 3d printer filament reel, perfect roundness and very tight diameter tolerance,approximately 68m of SILK filament on each spool ease of use,minimal warping,no clogging,no bubbles. Increase your 3d printing objects delicacy.. SUNLU 250G Spool DiameterSpool Diameter 120mm4.7inches, Spool Width 43mm1.69inches, Spool Hub Hole Diameter 42mm1.65inches. 250G spool size of the SUNLU filament spool is suitable for hanging on a lot of FDM 3D printers.. High Compatiblity Vacuum Pack SILK FilamentCompatible with 99 FDM 3D printers with heated beds and 3D pen.Vacuum packed neatly arranged SUNLU SILK 3d printer filament, provide better printing result.Environmental protection, 250g SILK filament is made from starch raw materials derived from renewable plant resources..

High-Quality PLA FilamentsMade of high-quality PLA, a commonly used thermoplastic material features lower melting temperature and ease of use, low warp and shrinkage, odorless during printing, and provides a glossy surface finish.. Dimensional Accuracy Consistency Strict tolerances guarantee these PLA filaments of 1.75 mm diameter much smoother and more stable printing with the dimensional accuracy of - 0.02 mm 1 kg spool 2.2lbs.. Less-tangle and Easy to UseFull mechanical winding and strict manual examination to ensure that the line is neatly arranged and less tangled, and to avoid possible snap and line breaking. A larger spool inner diameter design for easy feeding.. Clog-Free Bubble-FreeDesigned and manufactured with clog-free, superb layer bonding and great fluidity for smooth and stable extrusion. Complete dried for 24 hours before packaging and vacuum sealed with desiccants in the bag to protect the filament from moisture, no clogging and bubbling problems.. Wide CompatibilityUniversal compatibility with most of the common 1.75mm FDM 3D printers on the market due to the high-quality standards in terms of manufacturing accuracy and a small dimensional tolerance of - 0.02mm..

Quality Prints at High Speed With PowerBoost 2.0 technology and Ultra Direct Extruder, AnkerMake M5C can achieve printing speeds of up to 500 mms while maintaining 0.1 mm precision, so you can create quality models faster and more efficiently.. Easy Control From Anywhere With Wi-Fi and Bluetooth connectivity, you can control the printer, monitor the status of your prints, and transfer sliced models directly from your mobile device. The user-friendly AnkerMake app is easy to use for beginners and pros alike.. Next-Level Detail with Precision Mode This all-new feature supports up to 50 m resolution when using a 0.2 mm nozzle. Supported by multiple advanced algorithms, it makes fine printing faster and more efficient than ever before.. Enduring Reliability Wide Compatibility With wear-resistant components and a 300C all-metal hotend, this 3D printer is durable and versatile. It can handle a wide range of filament materials like PLA, PETG, ABS, TPU, and PLA-CF Carbon Fiber.. User-Friendly Features for Easy Printing This 3D printer has 49-point 7x7 automatic bed leveling, an integrated design for easy installation, and power and filament outage recovery functions. The PEI flexible magnetic plate provides a stable and easy-to-remove printing surface, making it an ideal choice for beginners..